(For both Objective and Conventional Type Papers)
Theory of Machines and Machine Design
Concept of simple machine, Four bar linkage and link motion, Flywheels and fluctuation of energy, Power transmission by belts – V-belts and Flat belts, Clutches – Plate and Conical clutch, Gears – Type of gears, gear profile and gear ratio calculation, Governors – Principles and classification, Riveted joint, Cams, Bearings, Friction in collars and pivots.
Engineering Mechanics and Strength of Materials
Equilibrium of Forces, Law of motion, Friction, Concepts of stress and strain, Elastic limit and elastic constants, Bending moments and shear force diagram, Stress in composite bars, Torsion of circular shafts, Buckling of columns – Euler’s and Rankin’s theories, Thin walled pressure vessels.
Properties of Pure Substances : p-v & P-T diagrams of pure substance like H2O, Introduction of steam table with respect to steam generation process; definition of saturation, wet & superheated status. Definition of dryness fraction of steam, degree of superheat of steam. h-s chart of steam (Mollier’s Chart).
1st Law of Thermodynamics : Definition of stored energy & internal energy, 1st Law of Thermodynamics for cyclic process, Non Flow Energy Equation, Flow Energy & Definition of Enthalpy, Conditions for Steady State Steady Flow; Steady State Steady Flow Energy Equation.
2nd Law of Thermodynamics : Definition of Sink, Source Reservoir of Heat, Heat Engine, Heat Pump & Refrigerator; Thermal Efficiency of Heat Engines & co-efficient of performance of Refrigerators, Kelvin – Planck & Clausius Statements of 2nd Law of Thermodynamics, Absolute or Thermodynamic Scale of temperature, Clausius Integral, Entropy, Entropy change calculation for ideal gas processes. Carnot Cycle & Carnot Efficiency, PMM-2; definition & its impossibility.
Air standard Cycles for IC engines : Otto cycle; plot on P-V, T-S Planes; Thermal Efficiency, Diesel Cycle; Plot on P-V, T-S planes; Thermal efficiency.
IC Engine Performance, IC Engine Combustion, IC Engine Cooling & Lubrication.
Rankine cycle of steam : Simple Rankine cycle plot on P-V, T-S, h-s planes, Rankine cycle efficiency with & without pump work.
Boilers; Classification; Specification; Fittings & Accessories : Fire Tube & Water Tube Boilers.
Air Compressors & their cycles; Refrigeration cycles; Principle of a Refrigeration Plant; Nozzles & Steam Turbines
Fluid Mechanics & Machinery
Properties & Classification of Fluids : ideal & real fluids, Newton’s law of viscosity, Newtonian and Non-Newtonian fluids, compressible and incompressible fluids.
Fluid Statics : Pressure at a point.
Measurement of Fluid Pressure : Manometers, U-tube, Inclined tube.
Fluid Kinematics : Stream line, laminar & turbulent flow, external & internal flow, continuity equation.
Dynamics of ideal fluids : Bernoulli’s equation, Total head; Velocity head; Pressure head; Application of Bernoulli’s equitation.
Measurement of Flow rate Basic Principles : Venturimeter, Pilot tube, Orifice meter.
Hydraulic Turbines: Classifications, Principles.
Centrifugal Pumps : Classifications, Principles, Performance.
Classification of Steels : mild steal & alloy steel, Heat treatment of steel, Welding – Arc Welding, Gas Welding, Resistance Welding, Special Welding Techniques i.e. TIG, MIG, etc. (Brazing & Soldering), Welding Defects & Testing; NDT, Foundry & Casting – methods, defects, different casting processes, Forging, Extrusion, etc, Metal cutting principles, cutting tools, Basic Principles of machining with (i) Lathe (ii) Milling (iii) Drilling (iv) Shaping (v) Grinding, Machines, tools & manufacturing processes.
About Staff Selection Commission
The Estimates Committee of the Parliament, in its 47th Report (1967-68), recommended the setting up of a Service Selection Commission for conducting examinations for recruitment to lower categories of posts. Pursuant to this, and as an interim measure, an Examination Wing was initially added to the Secretariat Training School, subsequently renamed as the Institute of Secretariat Training and Management (ISTM).
The Staff Selection Commission is an attached office of the Department of Personnel and Training and comprises of Chairman, two Members and a Secretary-cum-Controller of Examinations who are appointed on such terms and conditions as may be prescribed by the Central Government from time to time. The Commission is provided such supporting staff as considered necessary by the Central Government.
Tags: Staff Selection Commission SSC Syllabus Mechanical Engineering JE Exam SSC Syllabus Mechanical Engineering JE Exam 2011 Junior Engineer Exam syllabus download ssc JE Exam 2011 syllabus download downloads Staff Selection Commission syllabus download engineering subjects subject